Every type of dry & wet risers job we carry out, with when you need it, what's involved and how long it takes. Domestic, commercial and industrial.
Six-monthly inspections
Visual checks of inlets, outlets and cabinets.
- When you need it
- The riser has not been visually checked in the last six months.
- What's involved
- Inlet box, landing valves, caps, straps, cabinets and signs checked, with faults recorded.
- How long it takes
- Usually an hour or two per riser.
- Who it's for
- Domestic, commercial and industrial six-monthly inspections
Annual pressure tests
Wet testing to prove the riser holds pressure.
- When you need it
- The riser has no record of a pressure test in the last year.
- What's involved
- Riser filled through the inlet, pumped to test pressure and held, valves checked for leaks, then drained down.
- How long it takes
- Usually two to four hours per riser.
- Who it's for
- Domestic, commercial and industrial annual pressure tests
Valve repairs
Freeing or replacing seized landing valves.
- When you need it
- Landing valves are seized, leaking or failed a test.
- What's involved
- Valve stripped and serviced, or replaced with a matching valve, then tested under pressure.
- How long it takes
- Usually around an hour per valve.
- Who it's for
- Domestic, commercial and industrial valve repairs
Cap and cabinet replacement
Replacing stolen or damaged caps, blanks and cabinets.
- When you need it
- Caps, blanks, cabinet doors or locks have been stolen, damaged or vandalised.
- What's involved
- Missing or damaged parts replaced and cabinets secured with suitable locks.
- How long it takes
- Usually under an hour per floor.
- Who it's for
- Domestic, commercial and industrial cap and cabinet replacement
Wet riser servicing
Servicing wet risers, including pumps, tanks, valves and pressure checks, so firefighters have water on every floor.
- When you need it
- Your building has a wet riser due its routine service, or it shows pump or pressure faults.
- What's involved
- Pumps run, tank levels and pressures checked, landing valves tested and flow confirmed at the top outlet.
- How long it takes
- Usually half a day.
- Who it's for
- Domestic, commercial and industrial wet riser servicing
Inlet box repairs
Repairing or replacing damaged inlet boxes, glazing and doors at ground level so firefighters can connect quickly.
- When you need it
- The inlet box door, glass or lock is damaged, or the inlet itself is faulty.
- What's involved
- Damaged box parts or inlet replaced, non-return valve checked, then the box secured and signed.
- How long it takes
- Usually an hour or two.
- Who it's for
- Domestic, commercial and industrial inlet box repairs
Dry riser signage
Inlet and outlet signs fitted so firefighters can find riser connections quickly when they arrive.
- When you need it
- Riser inlet or outlet signs are missing, faded or damaged.
- What's involved
- Signs checked at the inlet and on every floor, and missing or damaged signs replaced.
- How long it takes
- Usually under an hour.
- Who it's for
- Domestic, commercial and industrial dry riser signage
Air release and drain valves
Servicing and replacing air release and drain valves so the riser fills properly and drains fully after use.
- When you need it
- The riser does not fill or drain properly, or the air release or drain valve leaks.
- What's involved
- Valves checked, cleaned or replaced, then proven during a fill and drain.
- How long it takes
- Usually an hour or two.
- Who it's for
- Domestic, commercial and industrial air release and drain valves
Riser pipe leak repairs
Finding and repairing leaks in riser pipework and joints found during pressure tests, so the riser holds pressure again.
- When you need it
- A pressure test has failed, or water is seen leaking from the riser.
- What's involved
- Leak traced, joint or pipe section repaired or replaced, and the riser retested under pressure.
- How long it takes
- Usually a few hours to a day.
- Who it's for
- Domestic, commercial and industrial riser pipe leak repairs
Riser anti-theft upgrades
Locking straps, secure cabinets and protected inlet boxes that help deter theft and tampering with riser valves and caps.
- When you need it
- Valves, caps or brass parts keep going missing or being tampered with.
- What's involved
- Vulnerable parts identified, then straps, cabinets or secure boxes fitted in a way that keeps fire service access.
- How long it takes
- Usually a few hours.
- Who it's for
- Domestic, commercial and industrial riser anti-theft upgrades