Every type of water safety & drinking water job we carry out, with when you need it, what's involved and how long it takes. Domestic, commercial and industrial.
Fittings compliance checks
Making sure water fittings are suitable.
- When you need it
- You are fitting out, changing use or have been asked to show fittings are suitable.
- What's involved
- Fittings and pipework inspected, unsuitable items noted and replacements recommended.
- How long it takes
- Usually a few hours.
- Who it's for
- Domestic, commercial and industrial fittings compliance checks
Backflow protection
Devices fitted and tested.
- When you need it
- Equipment could contaminate the mains supply through backflow.
- What's involved
- Risk category assessed, suitable devices fitted and tested, and results recorded.
- How long it takes
- Usually a few hours.
- Who it's for
- Commercial and industrial backflow protection
Tank inspections
Cold water tanks checked and cleaned.
- When you need it
- A cold water storage tank has not been checked for some time.
- What's involved
- Tank inspected for debris, lid and insulation condition, then cleaned and disinfected if needed.
- How long it takes
- Usually half a day.
- Who it's for
- Commercial and industrial tank inspections
Drinking water sampling
Drinking water samples taken and tested to check quality and confirm the supply is fit to drink.
- When you need it
- You have a private supply, a quality concern or new pipework in place.
- What's involved
- Sample points chosen, samples taken in sterile bottles and results explained.
- How long it takes
- Usually an hour or two on site.
- Who it's for
- Domestic, commercial and industrial drinking water sampling
Cold water tank replacement
Old, damaged or uncovered cold water tanks replaced with suitable covered tanks to keep stored water clean.
- When you need it
- Your tank is corroded, leaking or has no proper lid.
- What's involved
- Supply isolated, old tank removed, new covered tank fitted, insulated, connected and disinfected.
- How long it takes
- Usually a day.
- Who it's for
- Domestic, commercial and industrial cold water tank replacement
Pipework disinfection
New or altered water pipework flushed and disinfected before use so the supply is clean and safe.
- When you need it
- You have new pipework, a new tank or a system that has stood unused.
- What's involved
- System flushed, disinfectant added and held, then flushed again and sampled.
- How long it takes
- Usually a day.
- Who it's for
- Commercial and industrial pipework disinfection
Lead pipe replacement
Old lead water pipes replaced with modern pipework to reduce lead in your drinking water.
- When you need it
- Your property still has lead pipework on the incoming supply or inside.
- What's involved
- Lead pipe located, new pipework run and connected, and old sections removed.
- How long it takes
- Usually a day.
- Who it's for
- Domestic and commercial lead pipe replacement
Stop tap replacement
Seized or leaking stop taps replaced so the water supply can be turned off quickly in an emergency.
- When you need it
- Your stop tap will not turn, leaks or cannot be found.
- What's involved
- Supply isolated, old stop tap removed, new one fitted and tested.
- How long it takes
- Usually an hour or two.
- Who it's for
- Domestic and commercial stop tap replacement
Water supply notifications
Notifications to the water supplier prepared for works that must be reported before they start.
- When you need it
- You are planning new plumbing, a change of use or certain fittings.
- What's involved
- Planned works reviewed, the notification prepared and submitted and any conditions passed on.
- How long it takes
- Usually a few hours, plus the supplier's response time.
- Who it's for
- Domestic, commercial and industrial water supply notifications
Booster pump installation
Booster pumps fitted with suitable break tanks or protection to improve low water pressure safely.
- When you need it
- Upper floors or outlets have poor water pressure.
- What's involved
- Pressure tested, pump and any break tank fitted, controls set and outlets checked.
- How long it takes
- Usually a day.
- Who it's for
- Domestic, commercial and industrial booster pump installation