Every type of plumbing job we carry out, with when you need it, what's involved and how long it takes. Domestic, commercial and industrial.
Leak repairs
Dripping joints, burst pipes and hidden leaks traced and repaired, stopping water damage before it spreads through floors and ceilings.
- When you need it
- Water is dripping, staining a ceiling, or the meter moves with everything turned off.
- What's involved
- Supply isolated, leak located, the damaged joint or pipe section cut out and replaced, then tested under pressure.
- How long it takes
- Often an hour or two for a simple leak.
- Who it's for
- Domestic and commercial leak repairs
New bathroom plumbing
First and second fix plumbing for new bathrooms, with supplies and wastes run neatly to every fitting.
- When you need it
- You are fitting a new bathroom, en suite or shower room.
- What's involved
- Old fittings stripped out, new hot, cold and waste pipework run, then basin, toilet, bath or shower connected and tested.
- How long it takes
- Often two to four days, depending on layout.
- Who it's for
- Domestic and commercial new bathroom plumbing
Pipework replacement
Old lead, corroded or undersized pipework replaced with new copper or plastic, improving flow and reducing the risk of leaks.
- When you need it
- Pipes are lead, corroded, leaking repeatedly or giving poor flow.
- What's involved
- Existing runs traced, new pipework installed on the same or a better route, connected, flushed and pressure tested.
- How long it takes
- A day for small sections, several days for a whole property.
- Who it's for
- Domestic, commercial and industrial pipework replacement
Outside taps
Outside taps fitted with an isolation valve and backflow protection, ready for hoses, cleaning and garden watering.
- When you need it
- You need water outside for the garden, car washing or cleaning bins and yards.
- What's involved
- Wall drilled, supply teed off, isolation and check valves fitted, tap mounted and the pipework insulated against frost.
- How long it takes
- Usually an hour or two.
- Who it's for
- Domestic and commercial outside taps
Toilet repairs and replacement
Running, leaking or blocked toilets repaired or replaced, with new cisterns, fill valves and seals fitted as needed.
- When you need it
- A toilet keeps running, leaks at the base or will not flush properly.
- What's involved
- Fault diagnosed, worn parts or the whole pan and cistern replaced, reconnected to the waste and tested.
- How long it takes
- Often an hour or two; longer for a full replacement.
- Who it's for
- Domestic and commercial toilet repairs and replacement
Tap and valve replacement
Dripping taps, stiff stopcocks and failed isolation valves replaced, so supplies can be controlled and shut off when needed.
- When you need it
- A tap drips, a stopcock will not turn, or there is no way to isolate a fitting.
- What's involved
- Supply isolated and drained, old tap or valve removed, new one fitted, then tested for leaks.
- How long it takes
- Usually under two hours.
- Who it's for
- Domestic, commercial and industrial tap and valve replacement
Low water pressure fixes
Low pressure and poor flow investigated and fixed, from partly closed valves to undersized pipework and failing pumps.
- When you need it
- Taps run slowly, showers are weak, or flow drops when another outlet is used.
- What's involved
- Incoming pressure and flow measured, restrictions found, then valves, pipework or pump repaired or replaced.
- How long it takes
- Diagnosis often takes an hour; repairs vary.
- Who it's for
- Domestic, commercial and industrial low water pressure fixes
Kitchen and appliance plumbing
Sinks, dishwashers and washing machines plumbed in with proper supplies, valves and traps, so nothing leaks or smells.
- When you need it
- You are fitting a new kitchen, sink or appliance.
- What's involved
- Supplies and waste run to position, isolation valves and traps fitted, appliances connected and checked running.
- How long it takes
- Usually half a day to a day.
- Who it's for
- Domestic and commercial kitchen and appliance plumbing
Hot water cylinder replacement
Leaking or tired hot water cylinders replaced with new vented or unvented units sized to how much hot water you use.
- When you need it
- The cylinder leaks, hot water runs out quickly, or it struggles to keep up.
- What's involved
- Old cylinder drained and removed, new cylinder positioned, pipework adapted, controls connected and the system commissioned.
- How long it takes
- Usually a day.
- Who it's for
- Domestic and commercial hot water cylinder replacement
Blocked sink and waste repairs
Blocked sinks, basins, baths and showers cleared, with traps and waste pipes cleaned or replaced where needed.
- When you need it
- Water drains slowly or not at all, or wastes gurgle and smell.
- What's involved
- Trap and waste pipe checked, blockage cleared by hand or machine, damaged sections replaced and the run tested.
- How long it takes
- Often an hour or so.
- Who it's for
- Domestic and commercial blocked sink and waste repairs