Every type of heating installation job we carry out, with when you need it, what's involved and how long it takes. Domestic, commercial and industrial.
Boiler replacement
Old or unreliable boilers replaced with efficient new models, with the system flushed and the controls set up properly.
- When you need it
- The boiler keeps breaking down, parts are hard to get, or running costs are high.
- What's involved
- Old boiler removed, system flushed, new boiler, flue and filter fitted, then commissioned and the controls set up.
- How long it takes
- Usually one to two days.
- Who it's for
- Domestic and commercial boiler replacement
Radiator installation
New or replacement radiators fitted and sized to each room, so every space heats up evenly.
- When you need it
- A room is cold, a radiator leaks, or you are redecorating or extending.
- What's involved
- Heat requirement checked, system drained down, radiator and valves fitted, then refilled, bled and balanced.
- How long it takes
- Often half a day for one or two radiators.
- Who it's for
- Domestic and commercial radiator installation
Heating controls
Programmers, room thermostats, smart controls and radiator valves fitted, so heat comes on only where and when it is needed.
- When you need it
- Rooms overheat, the heating runs when no one is in, or the controls are old and confusing.
- What's involved
- Existing controls assessed, new thermostat, programmer or zone valves fitted and wired, then set up and explained.
- How long it takes
- Often half a day.
- Who it's for
- Domestic and commercial heating controls
Heat pumps
Air source heat pumps designed and installed with correctly sized radiators or underfloor heating, giving lower-carbon heating and hot water.
- When you need it
- You want to move away from gas or oil, or you are building or extending.
- What's involved
- Heat loss calculated, outdoor unit sited, cylinder and pipework installed, emitters upgraded where needed, then commissioned.
- How long it takes
- Often three to five days.
- Who it's for
- Domestic and commercial heat pumps
Boiler servicing
Annual boiler servicing that checks safe operation, cleans key parts and catches wear before it leads to a breakdown.
- When you need it
- The boiler has not been looked at for a year or more.
- What's involved
- Casing removed, burner, flue and seals checked, combustion tested, components cleaned and findings recorded.
- How long it takes
- Usually about an hour.
- Who it's for
- Domestic and commercial boiler servicing
Boiler repairs
Boiler breakdowns diagnosed and repaired, from no heating or hot water to pressure loss and fault codes.
- When you need it
- The boiler shows a fault, keeps losing pressure or stops heating.
- What's involved
- Fault codes read, components tested, the failed part replaced and the boiler checked running safely.
- How long it takes
- Often an hour or two, longer if parts need ordering.
- Who it's for
- Domestic and commercial boiler repairs
Power flushing
Sludge and debris flushed out of radiators and pipework, restoring heat output and protecting the boiler from damage.
- When you need it
- Radiators are cold at the bottom, the boiler is noisy, or a new boiler is going in.
- What's involved
- Flushing machine connected, system flushed with cleaning chemicals, radiators worked through, then inhibitor added and a filter fitted.
- How long it takes
- Usually a day.
- Who it's for
- Domestic and commercial power flushing
Underfloor heating
Wet underfloor heating laid in new floors and extensions, giving even warmth without radiators taking up wall space.
- When you need it
- You are building an extension, laying a new floor or want wall space back from radiators.
- What's involved
- Insulation and pipe laid to a planned layout, manifold and controls fitted, and the pipe pressure tested before the screed goes down.
- How long it takes
- Often two to three days, plus screed drying.
- Who it's for
- Domestic and commercial underfloor heating
Central heating installation
Complete central heating systems installed from scratch, with boiler, pipework, radiators and controls designed to work together.
- When you need it
- A property has no central heating, or relies on storage heaters or room heaters.
- What's involved
- Heat loss calculated, pipework run, radiators and boiler fitted, then the system filled, tested and commissioned.
- How long it takes
- Often three to five days for a house.
- Who it's for
- Domestic and commercial central heating installation
Commercial heating systems
Boilers, pumps and heating circuits installed and maintained for offices, shops, schools and other commercial buildings.
- When you need it
- A commercial building needs new plant, or its heating is unreliable or uneven.
- What's involved
- System surveyed, plant and pipework installed or replaced, controls set up, then commissioned and balanced.
- How long it takes
- Several days to a few weeks, depending on the building.
- Who it's for
- Commercial and industrial commercial heating systems